Hello everybody
I am New on enigma2 and is completely different to set My switch and LNB's.. I come from Coolsat's and Openbox's devices.
Using Vu+solo Se Hd (Black hole image). I have downloaded my satellite list
This is my installation:
LNB ==>> switch 4x4==>> switch 4x1 ==>> receiver
What I need to put
Reception settings
Configuration Mode: simple/advanced
Mode: positioner, ABCD, Toneburst A/B, disecq A/B
Set Voltage & 22 KHZ: yes/no
Send disecq only on satellite change: yes/no
What about switch 8x1?
what about LNB Universal?
thanks in advance
Results 1 to 10 of 37
-
Looking Help to set My Switchs and LNB's enigma2 – 04-11-2015,11:49 PM
-
04-12-2015,01:34 AM
Hello and Welcome to Legit!
I normally just use the advance lnb settings because every option is available. What are the 4X4 and the 4X1 switches connected to? What kind of lnbs do you have?
BlackHole is a nice image but it is missing some things that we need in North America. I would suggest you use a different image such as OpenVix to start with if you are in my part of the world..
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
04-12-2015,10:49 AM
If you ask me about the brands? I am using chieta 4x1 and channel master 4x4.... Finally my receiver I will put under 8x1(DMC) installation..this is why i am asking about 8x1 also
I have different static satellites using LNB Ku linear, LNB KU Universal, C Band.. No motorized and C/ku LNBF's thru my installation
-
04-12-2015,11:00 AM
Where are you located?
[Only registered and activated users can see links. ]
Look in post#12 in the above link and download the user manual for Vix. Enigma2 all operates almost the same and that manual gives a good description of how to set things up.
Information on how your antenna and fta system is set up would be nice, such as how the switches are connected together, and what lnb or other device is connected to each switch port. A diagram or drawing would help, but a good written description will work too.
-
04-16-2015,11:57 AM
Thanks Good Information..
Understanding what I am reading on This Manual
*The Manual said:
Disecq A,B,C,D(for 4/1 switch)
I guess:
port 1= A
port 2= B
port 3 =C
port 4 = D
Is Correct?
*In regards switch 4x4 (0 / 22 KHZ)
This is what the Manual said:
Futhermore You can set the Tuner to use Voltage and 22 KHZ(for polarization Horizontal/Vertical) switching and frequency band High/low): Normally set to "Yes" (default) and to send disecq Only on satellite change: Normally set to "No" (default)
I guess I need to Set "Yes" If my satellite is 4x4 side ON
I am Not sure If set "Yes" or "No" If My satellite is 4x4 side OFF
What you recommend??
-
04-16-2015,01:01 PM
I think you are correct on the ABCD diseqc switch.
On the 4X4, which switch do you have? What is the make/model?
-
04-17-2015,09:14 AM
-
04-17-2015,10:14 AM*In regards switch 4x4 (0 / 22 KHZ)
This is what the Manual said:
Futhermore You can set the Tuner to use Voltage and 22 KHZ(for polarization Horizontal/Vertical) switching and frequency band High/low): Normally set to "Yes" (default) and to send disecq Only on satellite change: Normally set to "No" (default)
I guess I need to Set "Yes" If my satellite is 4x4 side ON
I am Not sure If set "Yes" or "No" If My satellite is 4x4 side OFF
What you recommend??
[Only registered and activated users can see links. ]
-
04-17-2015,12:19 PM
Thanks .. I will try and let you know
-
04-18-2015,09:34 AM
If I am using LNB KU linear std . How I can set below values? Normally in FTA receivers set 10750
If I am using LNB universal . How I can set below values? Normally in FTA receivers set 9600 or 10600 or universal
If I am using LNB C band . How I can set below values? Normally in Fta receivers set 5150
I am not sure on enigma2 this values
LoF/L 097500000000000
LoF/H 106000000000000
Thresold
Also I am not sure if is:
10750000000000000000
"or"
00000000000010750
What means thresold?
Thanks in advanceLast edited by bronco; 04-18-2015 at 09:42 AM.