Page 4 of 5 FirstFirst 12345 LastLast
Results 31 to 40 of 43
  1. Collapse Details
    #31
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    Has the loader been configured for Com Port 5?

    You may also change the com port from 5 to 1 in the device manager of the computer. Normally, it will not hurt anything to do that, but it would depend on what has been assigned com port 1.
    Reply With Quote
     

  2. Collapse Details
    #32
    Join Date
    Dec 2012
    Location
    NE Ohio
    Posts
    73
    Post Thanks / Like
    EB Thanks, I changed to com port 1 in Device Manager and still getting the same. Thanks I think this receiver has had it!
    Reply With Quote
     

  3. Collapse Details
    #33
    Join Date
    May 2011
    Posts
    5,807
    Post Thanks / Like
    Have you contacted X2 to see is there is any warranty open?? How old is this receiver?? Have you try to recover using an old file from our files section different from the one marked as Recovery file in the loader rar file?? Maybe it will accept an older file.
    X2 Premium III HD, Openbox X5/ S10, Gsky V3/V6, iSmart m100
    Reply With Quote
     

  4. Collapse Details
    #34
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    It may be a good idea to test the rs232 serial connection on another receiver that works to verify that your computer is communicating with the receiver.
    Reply With Quote
     

  5. Collapse Details
    #35
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Quote Originally Posted by jdelanos73 View Post
    Thanks EB, I checked under the Device Manager, the driver for my Keyspan is listed under Serial Port COM5. When I change Port to COM5 The Message is -- Synchronizing STBs... Please reset target! And it just sits there with nothing happening. When I Cancel it says Downloading, but not really Downloading, I waited over an hour with still nothing happening.

    I don't even get the bar at the bottom showing the % of downloading.
    You will get these messages when the loader is connected to the computer, but not connected to the receiver. You need to have a Good, Null rs232 cable Connected to the back of the receiver and to the USB serial adapter.
    Reply With Quote
     

  6. Collapse Details
    #36
    Join Date
    Jun 2013
    Posts
    66
    Post Thanks / Like
    jdelanos73, I Bricked mine a couple of months ago. The cable I used was a 9 to 9 RS232. Pin out 2------3, 3-------2, 5--------5. And the shields were connected at each end. I think your better off to use a computer that has a 9 pin serial port rather than trying to use a usb adapter,If that's what your doing . I have found that sometimes those adapter don't work well with some things. Good luck.
    Reply With Quote
     

  7. Thanks ViP3R thanked for this post
  8. Collapse Details
    #37
    Join Date
    Feb 2012
    Posts
    7,247
    Post Thanks / Like
    +1

    Always better to use a dedicated serial port..... usb adapters do work BUT only if you are lucky to find the correct hardware compatibility.
    Reply With Quote
     

  9. Thanks ViP3R thanked for this post
  10. Collapse Details
    #38
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    A serial port on a computer today is very rare. Most computers made within the last ten years do not have them.
    Reply With Quote
     

  11. Thanks ViP3R thanked for this post
  12. Collapse Details
    #39
    Join Date
    Dec 2012
    Location
    NE Ohio
    Posts
    73
    Post Thanks / Like
    I want to thank everyone for trying to help me. I tried doing what everyone suggested in above posts. I will look for a receipt to send it back to factory. Thanks
    Reply With Quote
     

  13. Thanks el bandido thanked for this post
  14. Collapse Details
    #40
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Please let us know how it works out.....
    Reply With Quote
     

Page 4 of 5 FirstFirst 12345 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •