ATSC For Enigma2 (TEST)

[el bandido]

Here is a short video showing two ATSC tuners installed in one receiver. This setup works very well with two separate terrestrial antenna systems.

[eastof111]

Picked up a new Wintv850 and installed the atsc-usbhauppauge (1.0-r0) driver on Satdreamgr, cold reboot of receiver and no usb shows up under tuner configuration. Tried different usb ports and the usb stick does display the green led getting power.

Did I miss a step somewhere?

[el bandido]

Which image did you use? Did you use the one I posted?

Post the output of lsusb in telnet.

[eastof111]

I downloaded the image from the Satdreamgr site, Satdreamgr-4.0-gst1-vuduo2-20160509.

[el bandido]

2040 Is the device number as seen below.

satdreamgr-openpli-gst1 4 vuduo2


vuduo2 login: root
root@vuduo2:~# lsusb
Bus 001 Device 006: ID 2659:1211 Sundtek MediaTV Pro III (US)
Bus 001 Device 005: ID 734c:5925 TBS Technologies China
Bus 001 Device 004: ID 2040:7240 Hauppauge WinTV HVR-850
Bus 001 Device 003: ID 2040:7240 Hauppauge WinTV HVR-850
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 148f:5372 Ralink Technology, Corp. RT5372 Wireless Adapter
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@vuduo2:~#

We could try fixing what you have, but it will be easier to install this image because it contains everything that is needed without using telnet.
[Only registered and activated users can see links. ]

[eastof111]

Will try Satdreamgr-4.0-gst1-vuduo2-20160505 and see what happens. Thanks.

[eastof111]

Well, installed Satdreamgr-4.0-gst1-vuduo2-20160505 and still no Hauppauge in tuner configuration or lsusb. Beginning to wonder if I got a bad stick. It does power on and it does get warm to the touch.

[el bandido]

[Only registered and activated users can see links. ]

The image the above link works because I tested it before uploading it. I am not using multi-boot due to kernel and other issues. So it has not been tested in a multi-boot environment. These usb devices will not work unless the kernel with the correct modifications is loaded.

You may try to verify these packages being installed in telnet.
opkg update
opkg install kernel-module-xc5000
opkg install kernel-module-tveeprom
opkg install kernel-module-au0828
opkg install kernel-module-cx231xx
opkg install kernel-module-em28xx
opkg install kernel-module-tda18271
opkg install kernel-module-si2157

Verify the firmware file is installed:
cd /lib/firmware
ls
FW File =
dvb-fe-xc5000-1.6.114.fw (Should be in the list.)

Still not working?
Post a complete log file using:
init 4
ENIGMA_DEBUG_LVL=4 enigma2

I suspect the usb stick is good from what you have posted. Just need to find the problem or issue as to why it is not loading.

[eastof111]

Thanks, I know about Satdream and Pli not working with multiboot, that's why I installed it in flash. I'll do the opkg's tomorrow since I am recording currently using ATV.

[eastof111]

Still using Satdreamgr-4.0-gst1-vuduo2-20160505 in flash.

Prior to doing any opkg's checked to see if the dvb-fe-xc5000-1.6.114.fw was in the lib/firmware directory and it was.

Did the opkg's and:

opkg update
opkg install kernel-module-xc5000 is up to date
opkg install kernel-module-tveeprom is up to date
opkg install kernel-module-au0828 is up to date
opkg install kernel-module-cx231xx is up to date
opkg install kernel-module-em28xx is up to date
opkg install kernel-module-tda18271 is up to date
opkg install kernel-module-si2157 installed and configured

Cold reboot and still nothing in the tuner configuration display. Currently running the level 4 debug and will post as soon as it completes.