OK EB glad to hear that you received the NPR MUX using the MIO and the satdreamgr image. For some reason I cannot get a lock on the NPR transponder on the MIO. I get a solid 60% lock with the VU+ but not a blip on the MIO - strange. Also using satdreamgr 6.2 on the mio.
Thread: Edison mio 4K
Results 21 to 30 of 218
-
12-30-2018,12:23 PM
Last edited by rayydio; 12-30-2018 at 12:32 PM.
-
12-30-2018,01:20 PM
That transponder at 91W Ku for the raido channels is very difficult to lock. The MIO does not like it for some reason. To get it working, I just tune the radio channel or the transponder frequency and wait for it to open. Sometimes this takes 5 minutes or more. Other times, it will open in a few seconds. Go figure...
Here is a link to a video test of the 91W ku channels. I only found 2 with audio during this test.
[Only registered and activated users can see links. ]
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assrayydio thanked for this post
-
12-30-2018,03:41 PM
Found a screen where it says the tuner in the Mio4k is good for symbol rates 0-60. Looked at the vu+4k and it was only good for 1-45
To see the screen be in tuner configuration and have tuner A highlighted then press epg button. What ever tuner is highlighted when epg is pressed it shows some information. Ran the the blindscan plugin with 0-60 and it did good on 67w,Found and scanned in the 49000 symbol rate transponders. Did not find them using 2-49. I keep pressing epg for exit, it is backward from the vu+ zero 4k. Got to get use to that.
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Kiss My Assel bandido, rayydio thanked for this post
-
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
12-30-2018,04:10 PM
I have my blindscan plugin set to 60 or 60,000 for the top symbol rate.
I do not understand what the epg problem is or why you have to press epg to exit. Never heard of that.
DVBSnoop is also good for tuner information, plus it will show you the line frequency that is being used to send the signal from your lnb to the receiver. Here is an example:
root@osmio4k:~# dvbsnoop -s feinfo
dvbsnoop V1.4.55 -- [Only registered and activated users can see links. ]
---------------------------------------------------------
FrontEnd Info...
---------------------------------------------------------
Device: /dev/dvb/adapter0/frontend0
Basic capabilities:
Name: "Availink AVL6261"
Frontend-type: QPSK (DVB-S)
Frequency (min): 950.000 MHz
Frequency (max): 2150.000 MHz
Frequency stepsiz: 1.011 MHz
Frequency tolerance: 5.000 MHz
Symbol rate (min): 0.000000 MSym/s
Symbol rate (max): 60.000000 MSym/s
Symbol rate tolerance: 0 ppm
Notifier delay: 0 ms
Frontend capabilities:
auto inversion
FEC 1/2
FEC 2/3
FEC 3/4
FEC 4/5
FEC 5/6
FEC 6/7
FEC 7/8
FEC 8/9
FEC AUTO
QPSK
auto transmission mode
auto guard interval
auto hierarchy
FE_CAN_2G_MODULATION
FE_CAN_RECOVER
Current parameters:
Frequency: 1750.000 MHz
Inversion: OFF
Symbol rate: 0.000000 MSym/s
FEC: FEC 2/3
root@osmio4k:~#
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Kiss My AssMegatron817, rayydio thanked for this post
-
12-30-2018,04:21 PM
The buttons are backwards for the remotes. I'm use to the Vu+ remote. I think i'm pressing exit, but on the mio remote i'm pressing epg. The menu button is on the opposite side also. Just have to get use to it.
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Kiss My Assel bandido, rayydio thanked for this post
-
-
Post Thanks / Like - 3 Thanks, 0 Likes, 0 Kiss My Ass
-
12-30-2018,05:16 PM
Same results here. Someone has a lnb that is drifting or is off looks like. No wonder the MIO was having difficulties locking this transponder. Thanks for the solution!
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assrayydio thanked for this post
-
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assrayydio thanked for this post
-
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My AssMegatron817 thanked for this post