Page 3 of 3 FirstFirst 123
Results 21 to 28 of 28
  1. Collapse Details
    #21
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    I downloaded and installed the image in this link, which is the exact same image that should be shipped with a Titanium MIO:
    [Only registered and activated users can see links. ]

    Hauppuage 950Q and 955 were inserted into the MIO before the image was installed. The results are easy to see.
    [Only registered and activated users can see links. ]

    Sometimes when there is a hardware problem or hardware failure, people will mess with the software thinking that is the problem. Then when the hardware problem is solved, the firmware is messed up. This action or sequence of events is pretty common.

    Nothing is wrong with TNAP. The supported Hauppauge devices have been checked and are found to be working
    Last edited by el bandido; 12-18-2019 at 08:22 PM.
    Reply With Quote
     

  2. Thanks MikeB, ViP3R, Titanium thanked for this post
    Likes MikeB liked this post
  3. Collapse Details
    #22
    Join Date
    Jun 2013
    Posts
    256
    Post Thanks / Like
    Confirming that this is the TNAP image default on the OS Mio 4k STBs shipped from Titanium Satellite.
    Reply With Quote
     

  4. Thanks MikeB, el bandido thanked for this post
  5. Collapse Details
    #23
    Join Date
    Dec 2019
    Location
    USA
    Posts
    75
    Post Thanks / Like
    I reflashed the TNAP image and now it works with the 955q.
    Microwave techs are fully deviated.
    Reply With Quote
     

  6. Thanks el bandido thanked for this post
    Likes el bandido, MikeB liked this post
  7. Collapse Details
    #24
    Join Date
    May 2015
    Posts
    71
    Post Thanks / Like
    I can't get OpenPli 7.2 to display the Hauppauge 950Q on the available Turners window. I have all the drivers installed. It works fine with TNAP1 and OpenVIX latest image.
    AZBox Me, Edision OS Mio 4K, Octagon SF8008, and TBS 6903-X. DG-380 Motor on 1.2M Geosat Pro. 3ABN Dish @30.0°W. 2nd 1.2M looking @103.0°W KU-Band. 12FT Paraclipse Dish looking from 37.5°W to 111.1°W.
    Reply With Quote
     

  8. Collapse Details
    #25
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    What kernel version for PLI, or what is the image build date? Look in Menu--->About.
    Thanks.
    Reply With Quote
     

  9. Collapse Details
    #26
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    It looks like PLI is still on kernel 5.3, which means the 850 and 950Q are not supported. I have already written about this in another thread.

    [Only registered and activated users can see links. ]

    It should also be noted that ATSC support for the Hauppauge 850 and 950Q usb devices stopped for a brief period of time, probably only in images with a kernel of 5.2 and 5.3 due to driver issues. Support for the Hauppauge 850 and 950Q usb devices was restored in images for the MIO line of receivers using kernel 5.4.0 and 5.4.1. Most of the current images are using kernel 5.4.1, which supports all three ATSC devices.
    I try to post anything that would make life easier for North American MIO/MIO+ users in this section:
    [Only registered and activated users can see links. ]

    A lot of what is posted for the MIO receivers would apply to other enigma2 receivers.
    Reply With Quote
     

  10. Thanks Babadem thanked for this post
  11. Collapse Details
    #27
    Join Date
    Mar 2018
    Location
    West Central Florida
    Posts
    618
    Post Thanks / Like
    The openpli-7.2 release was bad timing with kernel 5.4.1 by about a week or so.
    Seems Openpli team does not change the kernel during the current release like satdreamgr and the OE images do so the next release of Openpli should be kernel 5.4.1 or newer whenever that happens.
    Reply With Quote
     

  12. Thanks el bandido thanked for this post
  13. Collapse Details
    #28
    Join Date
    May 2015
    Posts
    71
    Post Thanks / Like
    Quote Originally Posted by el bandido View Post
    What kernel version for PLI, or what is the image build date? Look in Menu--->About.
    Thanks.
    OpenPLi 7.2
    Build date 2019-12-31
    Last update 2020-01-13
    Kernel Version 5.3.0
    Last edited by Babadem; 01-17-2020 at 10:31 AM. Reason: added quotes
    Reply With Quote
     

  14. Thanks el bandido thanked for this post
Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •