Thread: Edison Mio

Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. Collapse Details
    Edison Mio
    #1
    Join Date
    Nov 2017
    Posts
    28
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    I have a Edison Os Mio 4k coming
    I was going to download some images to play with.
    Is there a sticky or a link here, on how to load images.
    I also saw it has multiboot, 4 slots
    Is that Satdreamgr the best for blind scanning

    Thanks for any advice
    Reply With Quote
     

  2. Thanks el bandido thanked for this post
    Likes MikeB liked this post
  3. Collapse Details
    #2
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,194
    Post Thanks / Like
    Welcome to Legit!
    Did you purchase the MIO or the MIO+?
    Is this your first enigma2 receiver?
    Where did you buy the receiver?
    Reply With Quote
     

  4. Thanks WaMan thanked for this post
  5. Collapse Details
    #3
    Join Date
    Nov 2017
    Posts
    28
    Post Thanks / Like
    I bought the MIO
    no, I have the vu zero 4K
    I bought it off ebay
    Reply With Quote
     

  6. Collapse Details
    #4
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,194
    Post Thanks / Like
    There are two types of images.
    The usb type will load through usb and will have a file named emmc in it.
    To install usb image:
    Download the usb image and unzip it to the mio4k folder.
    The the mio4k folder with files on an usb stick, and insert the usb stick into the rear of the receiver.
    Remove and then apply power to the receiver, and follow onscreen instructions for loading.
    USB type images that contain the emmc file will only install in slot 1 of the receiver.

    Multiboot images will contain a file named rootfs.tar.bz2.
    Multiboot images may be installed on any of the 4 slots of the receiver.
    The following instructions assume that you are using as PLI based image (OpenPLi or SatDreamGr) to flash from. Multiboot images are flashed "live", while the receiver is running.
    To install multiboot image:
    Download the correct multiboot image.
    PLi and SatdreamGr will have multiboot in the extension. OE Alliance images such as OpenATV, OpenVIX will not have multiboot in the file extension, but it will contain the rootfs, and the emmc file in the same folder. So OE Alliance images can be flashed as usb(slot1 only) or multiboot, OE Alliance downloads are much bigger because they have both types of files in the download.
    Place the Zipped multiboot image in a folder named downloaded_images, and install the folder onto an usb drive.
    Insert the usb drive into the receiver, and select Flash image in the menus. after a few seconds, the image(s) on your usb should appear. Follow online instructions for flashing.

    Ask if you need additional help. Flashing these images is easy once you understand how. You having previous experience with the Zero will help.
    Reply With Quote
     

  7. Thanks MikeB, WaMan thanked for this post
    Likes eastof111, WaMan liked this post
  8. Collapse Details
    #5
    Join Date
    Jun 2013
    Location
    Mid-Michigan
    Posts
    259
    Post Thanks / Like
    I HIGHLY recommend that you only use the image that comes with the receiver, UNTIL you get it tweaked the way you'd like it, and get a little used to it for a week or two while learning how it works. THEN think about installing other images in the other 3 slots.

    Trust me, you'll be much happier than trying to load and use 4 images right off the bat before you even know all the quirks of E2 receivers...
    My name is Mike.
    My posting name at Satguys is Primestar31
    Reply With Quote
     

  9. Collapse Details
    #6
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,194
    Post Thanks / Like
    Anyone that owns a Zero 4K already has enigma2 experience. There is no learning curve when changing between enigma2 receivers because the operating system is the same.

    The image that comes with this particular MIO will most likely be an out-of date OpenATV image, which will not scan good for North America. If this is the case, it should be deleted immediately.
    Reply With Quote
     

  10. Likes MikeB, WaMan liked this post
  11. Collapse Details
    #7
    Join Date
    Nov 2017
    Posts
    28
    Post Thanks / Like
    Receiver came today, noticed it has Satdreamgr 6 installed, I will try it out in the next few days,
    Thanks EB for the image install directions
    Reply With Quote
     

  12. Thanks el bandido thanked for this post
  13. Collapse Details
    #8
    Join Date
    Nov 2017
    Posts
    28
    Post Thanks / Like
    Question on my Edison Mio, I installed a second Satdreamgr from Legit download using multiboot instructions.
    I had no problems flashing, everything went smooth (thanks EB)
    I watched Tv about a hour before bedtime all was good, did not turn receiver off.
    When I got up, It was stuck on boot, I unplugged and replugged, it will boot up and play fine for about 15 minutes or so, then back to boot
    Do I need to reflash, maybe I got something corrupted.
    Reply With Quote
     

  14. Collapse Details
    #9
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,194
    Post Thanks / Like
    Please leave it like it is for a minute. Maybe we can find out what is wrong.
    Can you post the debug or crash log? One should be made every time it reboots. Check the /tmp folder of the receiver or in /home/root of the receiver, or in /hdd if an external hdd is installed. Look for enigma2_crash.log or similar. Zip this file and post it. Thanks.
    Reply With Quote
     

  15. Thanks WaMan thanked for this post
  16. Collapse Details
    #10
    Join Date
    Nov 2017
    Posts
    28
    Post Thanks / Like
    Ok I will try tonight, If time permits
    I was going to boot into 1st slot and see, if it does the same thing
    If not, I was going to try re flashing again #2 slot
    Thanks
    Reply With Quote
     

  17. Thanks el bandido thanked for this post
Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •