Page 1 of 8 123456 ... LastLast
Results 1 to 10 of 72
  1. Collapse Details
    TNAP-3 Test Images for OSMIO4K - Discussion
    #1
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    Discuss this Topic here.

    Link to files:
    [Only registered and activated users can see links. ]



    List:
    TNAP-3 only works with the 2.4 GHZ signal. See post#5
    Last edited by el bandido; 02-23-2020 at 08:07 AM.
     

  2. Thanks ViP3R, stephan94, norman881, Titanium, MikeB, mc6809e, Babadem thanked for this post
  3. Collapse Details
    #2
    Join Date
    Dec 2019
    Location
    USA
    Posts
    75
    Post Thanks / Like
    uptime 17 hours. looking good so far.
    Microwave techs are fully deviated.
     

  4. Thanks el bandido, ViP3R, Megatron817, Titanium thanked for this post
    Likes norman881, MikeB liked this post
  5. Collapse Details
    #3
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Good!

    We have a lot of control over this image, and can add or take away as needed. Let me know if you have any suggestions or comments about making it better.
    As an example, ATSC drivers will be pre-installed on the next version.
     

  6. Thanks ViP3R, mc6809e, Megatron817, stephan94, Babadem, Titanium thanked for this post
    Likes norman881, MikeB liked this post
  7. Collapse Details
    #4
    Join Date
    Nov 2012
    Location
    Eastern Washington
    Posts
    50
    Post Thanks / Like
    I installed this image on Wednesday and started playing with it today.. The menus are pretty similar to TNAP-1 with some different branches. I have only scanned 58 W. Everything looks good so far. I will know more after I get WebIF connected. Thank you VERY MUCH El Bandidio!

    Norman
    Last edited by norman881; 02-23-2020 at 09:14 AM.
     

  8. Thanks ViP3R, el bandido, stephan94, Titanium thanked for this post
    Likes MikeB liked this post
  9. Collapse Details
    #5
    Join Date
    Nov 2012
    Location
    Eastern Washington
    Posts
    50
    Post Thanks / Like
    My only problem was that I could not get OpenWebIF to connect. After several hours of on and off switching back to TNAP-1, I found the problem. TNAP-1 connects to the 5G signal. TNAP-3 only works with the 2.4 GHZ signal. I will scan more sats today and report any issues.
     

  10. Thanks el bandido, stephan94, ViP3R, Megatron817, MikeB, Titanium thanked for this post
  11. Collapse Details
    #6
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    I am surprised the 5G does not work in later versions, but does work in earlier versions.
    We can change to an earlier version of wireless lan if needed to fix this.
    Post #1 of this thread is updated to show the 5G problem.

    Thanks
    .
    .
    .
    Meine Dreambox One ist ein Stück Scheiße!.
     

  12. Thanks Titanium thanked for this post
    Likes norman881 liked this post
  13. Collapse Details
    #7
    Join Date
    Mar 2018
    Location
    West Central Florida
    Posts
    618
    Post Thanks / Like
    Quote Originally Posted by norman881 View Post
    My only problem was that I could not get OpenWebIF to connect. After several hours of on and off switching back to TNAP-1, I found the problem. TNAP-1 connects to the 5G signal. TNAP-3 only works with the 2.4 GHZ signal. I will scan more sats today and report any issues.
    Tested my 5g router and it did connect and OpenWebIF worked and was able to stream with Tnap-3.
     

  14. Thanks el bandido, ViP3R, MikeB, Titanium thanked for this post
  15. Collapse Details
    #8
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    OK
    We need to find out why one 5G connects and the other does not?
    Are both of these 5G routers open or password protected?
     

  16. Thanks Titanium thanked for this post
  17. Collapse Details
    #9
    Join Date
    Nov 2012
    Location
    Eastern Washington
    Posts
    50
    Post Thanks / Like
    TNAP-3 does not detect my Win 955Q at all. I've connected my antenna directly to the TV until I find a fix.
     

  18. Thanks el bandido, Titanium thanked for this post
  19. Collapse Details
    #10
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    The Hauppauge ATSC drivers are not pre-installed in the first mio4k test version. They will be pre-installed in the next version.
    To install Haupauge 955 driver:
    Verify the receiver has an internet connection
    Goto the Plugins menu and press the green remote button. A download list will populate.
    Select drivers from the populated list.
    Highlight the driver you want to install and press the OK button on the remote.
     

  20. Thanks ViP3R, stephan94, norman881, MikeB, Titanium thanked for this post
    Likes norman881, Babadem liked this post
Page 1 of 8 123456 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •