Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. Collapse Details
    Edision OS MIO 4K Tuner Intermittent
    #1
    Join Date
    Mar 2021
    Posts
    15
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    have two Edision Mio 4K’s. One on C Band and the other on Ku Band (different dishes). Had a momentary power outage (no storms). Both are powered through high end surge suppressors.

    Both will move the dishes to the appropriate position. The signal lock on both are now intermittent. I tried doing hard boots on both to no avail.

    It appears that something happened to the A-Tuners. I put an Openbox STB on the Ku system to see if it was outside hardware, etc. and all is working properly.

    Any suggestions would be appreciated before I declare both Edision’s DOA.
    Reply With Quote
     

  2. Collapse Details
    #2
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    You may declare whatever you want. DOA means Dead On Arrival. Your receiver powers up, so it is not Dead or DOA. It sounds like the receivers are probably healthy.

    If you want to fix the issue, then pick one of these receivers and supply information on how the antenna system is setup in the receiver along with a description of any switches that are in the antenna system and make/model of lnb(s) that are being used.
    Reply With Quote
     

  3. Collapse Details
    #3
    Join Date
    Jun 2013
    Location
    Mid-Michigan
    Posts
    259
    Post Thanks / Like
    Quote Originally Posted by dkendrick59 View Post
    have two Edision Mio 4K’s. One on C Band and the other on Ku Band (different dishes). Had a momentary power outage (no storms). Both are powered through high end surge suppressors.

    Both will move the dishes to the appropriate position. The signal lock on both are now intermittent. I tried doing hard boots on both to no avail.

    It appears that something happened to the A-Tuners. I put an Openbox STB on the Ku system to see if it was outside hardware, etc. and all is working properly.

    Any suggestions would be appreciated before I declare both Edision’s DOA.
    They have 4 image slots. So, flash a brand new fresh image to another slot (do NOT then load any backup over the top of that!), and see if that works, or acts the same. IF it works fine in another slot, reflash the image in the slot it was running on when it got corrupted.
    My name is Mike.
    My posting name at Satguys is Primestar31
    Reply With Quote
     

  4. Thanks el bandido thanked for this post
  5. Collapse Details
    #4
    Join Date
    Mar 2021
    Posts
    15
    Post Thanks / Like
    Will do.
    Reply With Quote
     

  6. Likes MikeB liked this post
  7. Collapse Details
    #5
    Join Date
    Mar 2021
    Posts
    15
    Post Thanks / Like
    Particulars for Ku System
    Two dishes. One fixed and other motorized with a Stab HH 90. One DISEqC switch utilizing Port A for the fixed and Port B for the motorized. The switch is between the positioner and the two dishes. Both LNB’s are INVACOM QPH-031 Quad Polar Ku Band.

    Settings are as follows and gave not changed since all was working properly:
    LNB — LNB 1
    Priority — Auto
    Type of LNB — KU STD 10750
    Voltage mode —Polarization
    Increased Voltage — On
    Tone Mode — Band
    DISEqC mode — 1.2
    Fast DISEqC — Off
    Tone burst — Off
    DISEqC 1.0 Command — Port A or Port B depending on dish selection
    DISEqC 1.1 Command — Off
    Sequence Repeat — Off
    Use USALS for this sat — Off for Port A and On for Port B depending on dish selection.
    Reply With Quote
     

  8. Thanks el bandido thanked for this post
  9. Collapse Details
    #6
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Really there are no right or wrong settings in fta as this is a hobby. But there are also settings that work and se3ttings that do not work.
    Let's make sure we have everything set where it will at least run before we go any further. The settings that need to be clarified or changed are shown below in red. You make no mention of the make/model of your lnbs, so it is assumed that 10750 is the correct l.o.

    LNB — LNB 1
    Priority — Auto
    Type of LNB — KU STD 10750
    Voltage mode —Polarization
    Increased Voltage — On
    Tone Mode — Band
    DISEqC mode — 1.2
    Fast DISEqC — Off
    Tone burst — Off
    DISEqC 1.0 Command — Port A or Port B depending on dish selection
    DISEqC 1.1 Command — Off
    Sequence Repeat — Off
    Use USALS for this sat — Off for Port A and On for Port B depending on dish selection.

    ]LNB — LNB 1
    Every lnb needs a separate number. We assume that each dish has a lnb, so you need settings or entries at least LNB 1 and LNB 2. (Enigma2 receivers can accommodate antenna systems that have up to 64 lnbs.)

    Tone Mode — Band
    Tone Mode should be set to Off for the 10750 l.o. lnb.

    DISEqC 1.0 Command — Port A or Port B depending on dish selection
    Port A should be assigned a lnb number. Port B should be assigned to a lnb number that is different from Port A.


    Use USALS for this sat — Off for Port A and On for Port B depending on dish selection.

    Same as above Port A and Port B should be assigned different LNB Numbers.
    Reply With Quote
     

  10. Collapse Details
    #7
    Join Date
    Mar 2021
    Posts
    15
    Post Thanks / Like
    Both LNB’s are INVACOM QPH-031 Quad Polar Ku Band.
    Reply With Quote
     

  11. Collapse Details
    #8
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Thanks.
    Is each lnb assigned a different lnb number???
    Reply With Quote
     

  12. Collapse Details
    #9
    Join Date
    May 2016
    Posts
    155
    Post Thanks / Like
    Check your external DC power supply's for the correct DC voltage output, and check the DC output at the receivers LNB input jack, if anything lower then +12.% volts DC then you have power problems.
    Reply With Quote
     

  13. Collapse Details
    #10
    Join Date
    Mar 2021
    Posts
    15
    Post Thanks / Like
    Both LNB's are asigned a differnet number.

    As I stated earlier, I hooked an OpenBox STB to the system in question and all works fine.

    All voltages on power supply and LNB's checkout OK.
    Reply With Quote
     

  14. Thanks el bandido thanked for this post
Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •