Results 1 to 10 of 72
-
TNAP-3 Test Images for OSMIO4K - Discussion – 02-19-2020,08:55 AM
Last edited by el bandido; 02-23-2020 at 08:07 AM.
-
Post Thanks / Like - 7 Thanks, 0 Likes, 0 Kiss My Ass
-
02-21-2020,11:55 AM
uptime 17 hours. looking good so far.
Microwave techs are fully deviated.
-
Post Thanks / Like - 4 Thanks, 2 Likes, 0 Kiss My Ass
-
02-21-2020,12:13 PM
Good!
We have a lot of control over this image, and can add or take away as needed. Let me know if you have any suggestions or comments about making it better.
As an example, ATSC drivers will be pre-installed on the next version.
-
Post Thanks / Like - 6 Thanks, 2 Likes, 0 Kiss My Ass
-
02-22-2020,10:39 AM
I installed this image on Wednesday and started playing with it today.. The menus are pretty similar to TNAP-1 with some different branches. I have only scanned 58 W. Everything looks good so far. I will know more after I get WebIF connected. Thank you VERY MUCH El Bandidio!
NormanLast edited by norman881; 02-23-2020 at 09:14 AM.
-
Post Thanks / Like - 4 Thanks, 1 Likes, 0 Kiss My AssMikeB liked this post
-
02-23-2020,05:50 AM
My only problem was that I could not get OpenWebIF to connect. After several hours of on and off switching back to TNAP-1, I found the problem. TNAP-1 connects to the 5G signal. TNAP-3 only works with the 2.4 GHZ signal. I will scan more sats today and report any issues.
-
Post Thanks / Like - 6 Thanks, 0 Likes, 0 Kiss My Ass
-
02-23-2020,08:06 AM
I am surprised the 5G does not work in later versions, but does work in earlier versions.
We can change to an earlier version of wireless lan if needed to fix this.
Post #1 of this thread is updated to show the 5G problem.
Thanks.
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Kiss My Ass
-
-
Post Thanks / Like - 4 Thanks, 0 Likes, 0 Kiss My Ass
-
02-23-2020,08:10 AM
OK
We need to find out why one 5G connects and the other does not?
Are both of these 5G routers open or password protected?
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My AssTitanium thanked for this post
-
02-23-2020,09:18 AM
TNAP-3 does not detect my Win 955Q at all. I've connected my antenna directly to the TV until I find a fix.
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Kiss My Assel bandido, Titanium thanked for this post
-
02-23-2020,09:42 AM
The Hauppauge ATSC drivers are not pre-installed in the first mio4k test version. They will be pre-installed in the next version.
To install Haupauge 955 driver:
Verify the receiver has an internet connection
Goto the Plugins menu and press the green remote button. A download list will populate.
Select drivers from the populated list.
Highlight the driver you want to install and press the OK button on the remote.
-
Post Thanks / Like - 5 Thanks, 2 Likes, 0 Kiss My Ass