Loaded a new sat file after putting the receiver to sleep. File from satellites-xml.eu see attached pix.
Blind scanned with bud and as you can see it is still scanning frequencies that are not in the new sat file table.
In the past have always used 10750-10750-10750 when connected to my 8x1 switch on port 1 without any problems. Now it's connected to a 2x1 switch with same settings and the result is no blind scan. Also, tried your numbers and it made no difference, including 12700.
I guess it's time for a fresh flash and start from scratch.
Thread: E2 on a new Atemio Nemsis
Results 21 to 30 of 115
-
12-01-2014,02:58 PM
-
12-01-2014,05:45 PM
I'm not sure what I see in your photos, but I always thought "blind" scan meant it was blindly looking at all frequencies at a pre determined spacing, usually just a few meg. Doesn't seem it would need files at all unless you are doing a automatic scan which only looks at TPs on file.
Still you may be on to something as I too have moved the lamedb and sat.xml in and out a few times.
My satfinder works fine, gets TPs in just a few seconds so again the switch, lnb, and dish are ok.C: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
4:2:2 AZminiMe slaved off C/Ku
-
12-01-2014,06:37 PM
Just re-flashed NFR, cleaned out the system bouquets, etc. Using the flashed sat.xml file, the bud blind scanned and found only two channels on tuner A. Did the same with the fixed dish and zero on tuner C. It's scanning in 6 meg increments and missing 11940.
Checked Satfinder and at least I can see my switches are working by the difference in dbs in tuner A and C.
-
12-01-2014,06:48 PM
Seeing most of the images use the same blind scan search engine, I would guess it should have the same effect. I guess I'll have to re-check the others too.
-
12-01-2014,07:19 PM
I got something to work right. I moved the cable from my main Ku dish (the one that has a universal lnb set up) and put it on tuner B. Using the universal lnb template it blind scanned in just a few channels with the dish pointed at 91w, all with freq listed above 12500. So I changed to user defined lnb template, 9750/10600 but with the tone set to "on" locks it to the hi band. It blind scaned in everything I usually see on 91w and then some, all with the correct TP frequency listed.
To summarize what I found today, Universal setup doesn't work correctly on any lnb as someone mentioned earlier.
User defined lnb setup works correctly with a universal lnb.
User defined lnb setup does not work with a single band Ku lnb.C: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
4:2:2 AZminiMe slaved off C/Ku
-
12-01-2014,07:21 PMC: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
4:2:2 AZminiMe slaved off C/Ku
-
12-01-2014,07:52 PM
Well, glad you have it working.
-
12-01-2014,08:47 PMC: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
4:2:2 AZminiMe slaved off C/Ku
-
12-02-2014,06:11 PM
So.. continuing on, if I can get some help from East or anyone who has a single band Ku lnb working correctly on E2 please take two steps forward
C: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
4:2:2 AZminiMe slaved off C/Ku
-
12-02-2014,08:16 PM
Pixl, you might post on the ATV or PLI forum and see if they have any recommendations.