Default 10-11-2013,12:14 AM Add to this user's reputation Add Infraction for dr.zin Report Post
I made the mistake of playing with another old receiver today and used that to set 72w to 97w which screwed up the settings for x2 when I switched back tonight.It took about an hour to get the settings correct again.
I did it same thing with my Openbox 9 and X2 ,,,But there is cure , -Antibiotic ..
Thread: X2 with DiseeqC 1.2 Motor
Results 21 to 28 of 28
-
10-11-2013,07:10 PM
Last edited by chifut; 10-11-2013 at 07:12 PM. Reason: ..
-
10-11-2013,09:04 PM
Diseqc 1.2 positions need to be stored in the motor or positioner box AND in the receiver.
Try these simple steps if you are having diseqc 1.2 storage problems and see if you get better results.
(1) If you have a Diseqc 1.2 positioner box with the satellite positions already stored, then you may unplug the box to increase setup speed.
If you have a Ku motor that has the correct Diesqc 1.2 positions stored in it, you may disconnect the coax feed from the receiver.
(2)The X2 will store the satellites in the order that they are selected in. Diseqc 1.2 position 1 will be assigned to the first satellite to be set up, Diseqc 1.2 position 2 will automatically be assigned to the second satellite setup...etc. Diseqc 1.2 position numbers are automatically assigned and cannot be changed as of today.
(3) Select the first satellite that you want to set up in the Antenna Setting Menu of the X2.
[Only registered and activated users can see links. ]
(4) Select Diseqc 1.2 in Motor and Press OK on the remote.
[Only registered and activated users can see links. ]
(5) Highlight "Store" in the Satellite Setting Menu, then Press OK on the remote.
[Only registered and activated users can see links. ]
(6) Make sure "Yes" is highlighted in Yellow and press the OK button on the remote.
[Only registered and activated users can see links. ]
(7) Repeat as needed until all of the satellites in your list have been stored.
[Only registered and activated users can see links. ]
(8) Apply power to satellite positoner. Reconnect Ku motor. Test for correct dish movement between the satellites.
Note: Diseqc 1.2 motor commands may be interrupted and all movement stopped if any button on the remote is pushed while the dish motor or actuator is moving.
Wait until ALL movement has stopped before pressing any remote buttons when programming satellite positions, scanning satellites, or while doing signal strength checks. EB.
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
10-11-2013,09:22 PM
Yep.tHat's the steps for storing the birds in diseqc 1.2 motor option
-
10-11-2013,09:53 PM
There is a trend now where receivers automatically assign diseqc 1.2 positions. I have a few that do that and they all cost considerably more than the X2.
The X2 stores the satellites in ascending numbers. I do not know how you can assign two satellites to have the same diseqc 1.2 position number, but you can assign most Ku motors and positioner boxes several different numbers for the same position.
As an example, I have positions 35 and 26 stored in my diseqc 1.2 positioner for the satellite at 103W. This allows me to have two different satellites that will stop the dish at the exact same position.
There are several work-a rounds available for the Hybrid satellite issue that you describe. The universal lnb setting may also be changed to accept most c/ku combination lnbs.
Hopefully a future firmware will allow us to have user adjustable diseqc 1.2 positions. EB.
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
10-12-2013,05:35 AM
Neither of my 2 stand alone positioners allow 2 sat positions to be saved for the same bird. For example, F3 is stored on my Pansat ap3500 for Amc 6 at 72w, if I store A1 for the same position then I will only be able to use A1 to get back to that sat as the saved info automatically replaces the old saved position. I would suggest saving the sat position then slightly nudging the dish east or west and saving that position as well would work for the same satellite.
-
-
10-13-2013,11:43 PM
THE RECEIVER IS DEFECTIVE AND I'M GOING TO ASK X SQUARE TO REPLACE IT IF/WHEN THEY REPLY TO THE MESSAGE I SENT THEM!
OK. Why don't we just leave it at that?
I have tried to help you and that is all I am going to do.
Your links to other sites have been removed. I am not going to draw this out between two message boards. Do not post any more links to other sites. It is hard enough keeping up with what goes on here much less somewhere else.
I see no need to continue with this thread because you have decided you received a defective, used, receiver.
Thread Closed. EB.
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
10-14-2013,07:29 AM
WOW!!! I have been slipping in and out of here for the past few days between work and trying to get ready for the family to arrive for Thanksgiving dinner, yesterday, so didn't have much time to read all the posts. EB..........THANKS!!!!!!!!! I just sat down, followed your very well layed out instructions and, bingo, it worked. I only set up the positions for 103W and 101W, just to see if it would work but even that would not work before. Again, thanks, and I do believe that Lone Gunman will be much happier at SatGuys.
Optibox Anaconda, X2, OpenBox-S9, CS8000 and 2 X CW700S, 7 1/2' Perfect Ten scanning 55W to 139W C Band and a 39" Q-Sat scanning 30W to 125W Ku Band