Hello El Bandido,
I do not understand very well .
I just made an online update for the driver
(I unplugged the MIO4K after 20 minutes because it was left with the update message without restarting itself)
after reconnecting the MIO4K it has restarted normally and in the information appears with the driver 2021 01 07
and the 5.9.0 kernel ??
it's amazing
why the update is not done ?if it doesn't work online, how can i do it by myself?
stephan94
Results 41 to 50 of 70
-
06-02-2021,08:41 AMEdision OS mio4K and Ustym 4K Pro with TNAP-5.1 ; Channel Master 1,80 ; TBS6983
LNB Ku Band . LNB KA Band 18200-19200 /21200-22200,LNB C band
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Kiss My Assel bandido, ViP3R thanked for this post
-
06-02-2021,09:07 AM
There is no 5.9 kernel on the TNAP-4 server, so try flashing the image. Do this:
Backup your settings
Put Good Blank or Empty usb drive in the receiver
Select Flash image in the receiver (Menu--->Setup--->Flash image).
Select the Tnap-4 06-02-2021 and press the OK button on the remote.
Select the correct image slot (with backup). Press the OK buitton on the remote.
Wait 5-10 minutes for the image to flash and restore settings.
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Kiss My Ass
-
06-02-2021,11:42 AM
Thank you so much ,
it worked perfectly.
I was with the first version of Tnap 4.0
that's why it didn't work.
have a good day
But as I understand it now T2MI works all the time?
it is no longer necessary to switch from "NoT2MI" to "T2MI"
like we did before.Edision OS mio4K and Ustym 4K Pro with TNAP-5.1 ; Channel Master 1,80 ; TBS6983
LNB Ku Band . LNB KA Band 18200-19200 /21200-22200,LNB C band
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
06-02-2021,11:45 AM
Correct.
These are T2MI Drivers.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assstephan94 thanked for this post
-
06-02-2021,12:00 PM
Be sure to remove any T2MI or Non-T2MI plugins before flashing. If you have installed these plugins and do not remove them, then system restore will Install them again.
To remove plugins:
Menu---> then press red remote button (see below).
[Only registered and activated users can see links. ]
Delete the T2MI and Non-T2Mi then re-flash the image. On your About page, It looks like you flashed the image with the Non-T2MI plugin installed and system restore installed it!
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assstephan94 thanked for this post
-
06-02-2021,12:20 PM
It's annoying I just reinstalled everything, including the plugins or skins that are not recognized by the MIO4K
is it really essential?
when I uninstall the "NOT2MI" the "T2MI" appears next to Kernel version 5.12
and we cannot uninstall it or else it is removed but the indication next to 5.12 is still there
on the other hand the blindscan always works well (including with the small sr close to each other)Edision OS mio4K and Ustym 4K Pro with TNAP-5.1 ; Channel Master 1,80 ; TBS6983
LNB Ku Band . LNB KA Band 18200-19200 /21200-22200,LNB C band
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
06-02-2021,01:29 PM
The indication next to 5.12 is still there because the "About" file has not been changed. I will fix that later, and will update the extra T2MI plugin later today. The T2MI driver that is in the extra feeds now is the old T2MI driver and should be removed.
-
Post Thanks / Like - 4 Thanks, 2 Likes, 0 Kiss My AssMegatron817, stephan94 liked this post
-
07-26-2021,07:38 PM
Is the update server OK? I just reinstalled TNAP 4.0 from the last multiboot image to (hopefully) fix the problem of the time reverting to 1970 (that at least four people other than me on SatelliteGuys are having since the last update) and when I tried to update from the network again, after rebooting it was still only indicating TNAP 2021-02-20 and Enigma2 2021-02-14. I tried the network update again and this time it only downloaded one more file, but when rebooting it got stuck on "boot". I pulled the power and it booted normally, but still only on the un-updated version. I also note that the kernel version still says NO-T2MI. Before my prior re-load to fix the wifi, I had a system fully updated to this month or last, including the latest T2MI driver. I haven't done anything different.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My AssMikeB thanked for this post
-
07-26-2021,08:36 PM
I can't answer your question, but I am one of the people with TNAP 4.0, where NTP time suddenly is not keeping proper time anymore. I finally gave up on that, and am now using transponder time, specifically, the Bars & Tone channel on AFN 3900 V DVB-S2 8psk 27500 2/3 as a startup service. It now once again keeps perfect time using that.
I believe that NTP time is for some reason, suddenly not working right only IF you keep your Mio in Standby, when you aren't specifically using it. Not sure why it's doing that again all of a sudden, as I haven't updated my Mio for a couple months.
I have full view of my Mio's front screen while sitting in my living room chair, and I could see the clock suddenly change to a totally random time for NO REASON. This only happened while it was in Standby mode. It might happen multiple times a day, then not happen for a while. Oh, and my Mio is hardwired to my router, which is only 2 feet away from it, and my router keeps perfect time.
This is the image I am using:
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]Last edited by MikeB; 07-26-2021 at 08:44 PM.
My name is Mike.
My posting name at Satguys is Primestar31
-
07-26-2021,09:43 PM
Anything about the operations of TNAP that is discussed at SatelliteGuys or other forums may not be seen or known about! It is hard enough to keep up with one forum. Searching the Internet for issues with TNAP is not a good option. Post any complaints, suggestions, or comments that you want to be known about the operations of TNAP on this site because this is where the image is assembled.
The best thing to do before doing any updates or upgrades is to make a full image backup using the backupsuite plugin. Doing this makes sense because it gives a complete restore point. If you cannot backup the whole image, at least backup and save the settings.
Loading a TNAP image dated 2021-02-20 then trying to update it online would most likely result in failure. There were several hundred package changes between what was available in 2021-02-20, and what is on the server now. A lot of things changed in 4 months. It is a good idea to flash to a newer image and not try to update a several month old image online. You can expect failure when you do this.
Images from May are available in the forum. These images should work well, and should not have any time issues. Links to these images are below.
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]
There is a test image on the server that can be flashed. Since it is a Test image, it may not work the way you would like. I do not suggest flashing it.
What is on the TNAP 4.0 server should work fine with the May image that is available for downloading in the forums. A newer version of TNAP should be available in the next few weeks.
-
Post Thanks / Like - 4 Thanks, 2 Likes, 0 Kiss My Ass