TNAP images currently Does Not have a frequency spacing rule or requirement for transponders. Most enigma2 images require transponders with the same polarity to be spaced 2 or 4 MHZ apart.
Shown below, the MIO4K logged a transponder at 3929V and another transponder at 3930V on a blindscan of 117w. This is sort of a moot point in this case because neither transponder had channels or even a lock. But there are other transponders in the world that are spaced less than 2MHz apart that have channels or services. The Blindscan in TNAP is currently unfiltered and unregulated. Whatever is found is shown and scanned with very few exceptions. Really the only rule being it has to be a satellite transponder or at least resemble one.
[Only registered and activated users can see links. ]
Thread: TNAP-5.1 Image Discussion
Results 61 to 70 of 181
-
04-29-2024,11:50 PM
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Kiss My Ass
-
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
04-30-2024,11:09 AM
Just found that I can't remove softcam-ncam:
[Only registered and activated users can see links. ]
also, when switching from one transponder to another, the signal jumps to the sky (45db, 26db, etc), before settling to whatever is normal:
[Only registered and activated users can see links. ][Only registered and activated users can see links. ]
On a dead tp is doing the same:
[Only registered and activated users can see links. ]Last edited by lme; 04-30-2024 at 11:29 AM.
Nihil sine Deo !
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
04-30-2024,01:38 PM
In terminal, Enter this command: opkg remove --force-remove enigma2-plugin-softcams-ncam
REBOOT
Check installed Plugins.
Let me know if that does not work.
For the signal issue, Is Allow signal below lock turned On or Off?
Online updates should fix the signal meter shown in post#62.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Asslme thanked for this post
-
04-30-2024,03:44 PM
Last edited by lme; 04-30-2024 at 04:06 PM.
Nihil sine Deo !
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
04-30-2024,06:21 PM
As a test, set "Allow signal below lock" to ON. see what effect that has on the signal level.
As another test change the skin for something simple and one that does not poll a lot. Try PLi HD night or something similar.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Asslme thanked for this post
-
04-30-2024,06:43 PMNihil sine Deo !
-
04-30-2024,08:02 PM
Okay. Attach what you replaced.
I don't think there has been any updates to Satfinder in at least six months. Be interesting to see what you replaced with what we have. Thanks..
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
05-01-2024,07:12 AM
Please use the private message system (pm) for random chatter that has nothing to do with this thread.
So Without making any other changes, installing that satfinder plugin makes your receiver run correctly, yes? What else is broken or in need of repair?
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Asslme thanked for this post