Yes, Uclan Ustym has this. I do not know how it will work on Eastern satellites. Let me know if youi have problems.
Thread: TNAP-5.1 Image Discussion
Results 141 to 148 of 148
-
05-09-2024,05:09 AM
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assstephan94 thanked for this post
-
-
05-09-2024,09:54 AMEdision OS Mio+ 4K UHD w/TNAP 5.1, 4-foot motorized Fortec offset dish (150W to 82W), Invacom QPH-031 Ku linear/circular LNBF, Titanium C1PLL LNBF. 41-inch Star Choice: 81W to 77W, Avenger PLL universal LNB. Shaw 60e elliptical dish 103W/99W. Hauppauge 950Q OTA USB, Clearstream 2V, CM-7777 preamp.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
05-09-2024,10:47 AM
Thanks for all work.
Good to see transponders with low symbol rate.
I need test signals before lock, but I need 1 transponder to test here in Brazil with my motorized dish 5m (117w to 20e) with 3 kind of lnbf.
I'll post same things that need to fix with ISDB-T, same as OpenPli.
Tune the transponders, but don't store the channel names, then appear unavailable. OpenATV/OE-Alliance show correctly.
This post below using Vuzero4k, but happens for all OpenPli images (I tried all my boxes here using same both ISDB-T usb adapters: sf8008, osmini4k, h9se, etc)
[Only registered and activated users can see links. ]
See:
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]
[Only registered and activated users can see links. ]
Thanks
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
05-09-2024,01:41 PM
@ frankviana,
I think we can fix that...Maybe.
Please start a thread on it in this section:
[Only registered and activated users can see links. ]
Need to use just one receiver. The Sf8008 Supreme would be nice.
The image needs to be setup on a slot by itself as a fresh install. Consider it to be a test image as we might mess it up.
The image needs one scan of DVB T. Do not add any satellite channels or services. Just one scan of DVB T.
Make a debug log of the DVB T scan. In telnet, use this command before the DVB T scan:
init 4
ENIGMA_DEBUG_LVL=5 enigma2 > /tmp/dvb-T-debug.log 2>&1
After the scan completes, get the dvb-T-debug.log from /tmp of receiver files and attach it.
Then you need to attach the settings file, and the lamedb file located in /etc/enigma2 of receiver files.
Finally, In telnet, need the output of: cat /proc/bus/nim_sockets
If you can start a thread in the proper section and do all of that, we may have enough information to see what the problem is. Most likely, a small change will need to be made in enigma2, which means an image will have to be built. But we will see...
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assfrankviana thanked for this post
-
05-09-2024,06:58 PM
Ok my friend.
I'll create new topic and will see.
I have sf8008 4k (not supreme) and osmini4k. Both don't work... All OpenPli don't work DVB-T/ISDB-T (siano and dib0700) tuners here.
We need this tuner working, because now, only OE-A works.
Among the countries that adopted this system are Argentina, Bolivia, Brazil, Chile, Costa Rica, Ecuador, Japan, Paraguay, Peru, Uruguay, Venezuela. In the testing or implantation phase are Angola, Philippines, Suriname and Botsuana.
I'll send you the logs and all that you need to solve.
Thanks
==================
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
05-09-2024,07:04 PM
Use the SF8008. Just easier for me maybe.
Most likely, the problem is identification. The channels scan, but they probably end up being listed as something else. So the receiver cannot link the DVB T tuner to the channels scanned with DVB T tuner. We will see.....
-
05-09-2024,09:15 PM
Impossible sf8008 because we have 2 problems using OpenPli:
Appear s2x instead DVB-T and.... if solve DVB-T, we have same gray channels (no store refference channels). First, need fix nim_sockets and after, second problem.
[Only registered and activated users can see links. ]
Osmini4k need fix only second problem (gray channels)
For SF8008 and osmini4k, only SPA fixed both problems (appear DVB-T and store all channels). For sf8008, OpenATV appear as S2X too (no way to test DVB-T).
[Only registered and activated users can see links. ]
Thanks.