Results 11 to 20 of 21
-
10-14-2022,05:35 PM
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
10-14-2022,08:52 PM
TNP 4.2 uses the same diseqc and lnb commands as TNAP 4.1 and TNAP 4.0. So it is doubtful the image is the problem. You may post your settings file in /etc/enigma2 if you continue to have problems.
-
10-14-2022,10:15 PM
I will keep watching to see how things go. The cozi problem was it was switched to a C band LOF ! Is there a specific exit sequence that should be used after saving a setting? I'm with you I highly doubt there is a problem with this version but thought I'd check to sure since it has happened more than once. FWIW the USALS seem to show a slightly different calculation that the previous version. I had to move my dish maybe 1/4 inch west to lock and ID 87 So maybe my motor problems are over I
l will check that out after tomorrow when my wifes shown on LPB records tomorrow LOL
Thanks for the help! And Thanks for your work on compiling this version!!Backwoods FTA
No OTA, Well Actually one carrier now
-
10-14-2022,10:24 PM
Thanks for the confirmation. The problem is that sometimes after setting a LNB LO next time you switch to a KU signal the LO may be 10750 or 5150 instead of say 10600
Bound to be something very simple I'm doing after setting up the LNB. I did notice that one of my fixed dishes was on the wrong port.Backwoods FTA
No OTA, Well Actually one carrier now
-
10-14-2022,10:26 PM
As mentioned in post#11, Each lnb needs a different lnb number.
.
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
10-14-2022,10:34 PM
Yeah I'm aware of that and I started from scratch at LNB 1 and configuring it as 10750 2 as 5150 and 3 as 10600
Maybe that will alleviate my problem. So far it's done fine
Thanks for the suggestion!
WTBackwoods FTA
No OTA, Well Actually one carrier now
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
01-24-2023,05:55 PMEdision OS Mio 4K, Invel DVB 3612, 12ft Conifer Mesh Bud, DMX 741 LNBF, V-Box 7 Positioner, Thomson Saginaw Actuator, Primestar fixed at AMC21, Channel Master CM-7000.
-
01-24-2023,09:49 PM
Some Pluto commercial breaks are ok on some channels. I got a plugin AJ Player Bar that I use to restart the stream when it needs it but it still not perfect. Some of the streams jump back a few minutes when refreshing. The Pluto VOD plays fine on tnap 4.2 but the time remaining counter gets off so you don't know how much longer the show or movie is a lot of the time. tnap 5. is not good for the Pluto VOD is freezes up alot can't finish the show.
-
01-25-2023,02:23 PMEdision OS Mio 4K, Invel DVB 3612, 12ft Conifer Mesh Bud, DMX 741 LNBF, V-Box 7 Positioner, Thomson Saginaw Actuator, Primestar fixed at AMC21, Channel Master CM-7000.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Kiss My AssMegatron817 liked this post
-
02-05-2023,01:45 PM
Will it be possible for you to enable the option to install oscam please