Hello
I have these equipment and need to connect them correctly
Receiver: Edision 4K mio+ (TNAP 5.0 image)
Motor: STAB HH120
Diseqc Switch: Axing SPU 81-00, 8 inputs, 4 committed (A, B, C, D) and 4 uncommitted (E, F, G, H). Input H allow DC pass through to connect motor to this position.
LNB: Universal
How should I configure the receiver to get the system working properly?
Results 1 to 10 of 29
-
STAB HH120 Diseqc motor connection through a Diseqc switch – 02-27-2024,08:18 PM
-
02-27-2024,09:16 PM
You have it wired wrong if the diagram is correct. The STAB HH120 is a good motor, but you cannot put most brands of diseqc switch in front of it. It has to be wired like this: Receiver--->STAB HH120--->Diseqc switch--->LNB(s).
-
02-28-2024,02:15 AM
Only one LNBF? Why would you need a Diseqc switch? Keep it simple,
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My Assel bandido thanked for this post
-
02-28-2024,08:12 PM
Actually I have 5 LNBs. 4 LNBs on three fixed dishes, one of the dishes (90 cm) with two LNBs with a multifeed setup and the 5th LNB mounted on the dish moved by the motor.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Kiss My AssMikeB thanked for this post
-
02-28-2024,08:28 PM
El bandido,
It is supposed that this switch is prepared to manage a Diseqc motor. See image below.
[Only registered and activated users can see links. ]
A question, does the receiver send the Diseqc command starting from top to bottom on the setup page (see blow), I mean first the Diseqc 1.2, later the Diseqc 1.0 and later the Diseqc 1.1?
[Only registered and activated users can see links. ]
How should I configure the LNBs in the receiver setup page, remove the Diseqc 1.2 and keep the Diseqc 1.0 or 1.1??
In the case I connect one of the LNBs to the uncommitted ports (E, F, G or H), if I select the E port, for example, what input should I select, Input 1 (1st input of the uncommitted part of the switch), or Input 5 (5th input of the whole switch) on the receiver?
-
02-28-2024,08:29 PM
Which switch brand can I use to keep it connected as it is now?
-
02-28-2024,09:29 PM
Have you got this switch working correctly with all lnbs Except the motor?
-
02-29-2024,05:05 AM
Yes, perfectly working. I configured as Diseqc 1.0 and assigned Port A, Port B, Port C and Port D (Committed switch configuration) for the first 4 LNBs.
-
02-29-2024,05:07 AM
I got these answers from the switch manufacturer.
Hello,
you need Position + Option + Uncommitted_1 and DiseqC 1.2. Position is the last one so BB and option 2.
Or position 4/8 and option 2, but you need DiseqC 1.2 for the motor.
Hello,
I'm sorry but I don't know your receiver. You need to set Diseqc 1.2 for the Rotor and select the correct output. Where it now says Disec 1.0, you need to select 1.1 for the Port and where it now says 1.1, you need to select 1.2 for the rotor.
I don't know your receiver and it would be better if you asked the manufacturer about this, or ask in Internet forums.
-
02-29-2024,06:01 AM
Are you running the motor in diseqc 1.2 or in USALS?