TNAP-7 Image Discussion

The 0405 image has been uploaded and contains several updates. Re-flash the image for best results.
An online update may not get all of the updates.

EnoSat said:
If I delete the other unnecessary languages, it always switches to English after a restart
View attachment 19736
Even though the option to not display them graphically is selected, the options are still displayed graphically
View attachment 19737
Click to expand...
The language and radio display during a scan should be fixed.


cyberham said:
I installed the new 0327 image. Webif issue remains. If I download any of the Classic, Documentary, Entertainment or Series bouquets then no bouquets are displayed in Webif. If I just delete those bouquets then Webif displays all bouquets.
Click to expand...
Editing bouquets in webif should be fixed. The 4 bouquets you uploaded were tested to work.


EnoSat said:
Do you think it would be possible to add a firmware selection option in addition to the driver selection ?
View attachment 19739
firmware 1.8.27679 - EDISION - wihout suppoer ShortFrameFEC
View attachment 19740
firmware 1.8.29209 - AVAILINK - with support ShortFrameFEC
View attachment 19741

PS: Would it be possible to add the NIT position from PID 16 to near the ONID/TSID as in OpenViX ?
View attachment 19742View attachment 19744
View attachment 19745
Click to expand...
Adding the firmware is possible, but not right now as there is other work to do.
You want to display in signal finder like VIX which is fine, but this is a skin issue and would need edits for each skin that is not VIX. The information wanted is already generated. The skin just needs to be adjusted to show it.


stazeb said:
Is there anyway to display Picons in the channel list on my Qviart Dual 4K
When I try to show in the channel list from menu Settings I receive this message
Click to expand...
What image does not display Picons? You uploaded a debug log but showed a crash log in the screenshot. Debug logs are no longer generated so the image was probably a bit old. Anyway, try the new image and see if the Picon issue is fixed. If not, then upload the crash log. Thanks


EnoSat said:
v2703 MIO4K+ - It happens quite often that if I’ve had Signal Finder running for a while and want to change the frequency, the app crashes; however, if I change the frequency gradually, it works fine (except for the occasional freeze or display of the level from the previous transponder when the current one is inactive—but that’s a different issue).
View attachment 19748
Click to expand...
Signal finder has been rebuilt. Test for effects...


jimmyjet said:
I just did a clean install of sf8008-20260328 MultiBoot Image on my Octagon SF8008 v1. Happy to report the WLAN drivers were installed and the Network functionality worked exactly as expected. The setup went flawlessly until I Saved and Exited from the default setup menu when the unit green screened and a crash log was displayed. I rebooted and all has been well ever since. I've attached the crash log for your review.

Observations: the first run boot and install seemed much faster than previous builds. The only negative, after I scanned 12000 v 20000 on 101°W SES1 and the Mood Music channels did not display as I had hoped from the recent forum discussions. I did a Signal Finder Scan on the Transponder and also a Blind Scan on the entire Satellite. I did find the Mood Music channels in the services menu but they don't play as expected.

Otherwise, this is the most stable and polished version of TNAP 7 that I have installed and used. I'll make it my daily driver for the week. Thanks for all of your hard work!
Click to expand...
Your crash that was shown in Network has been addressed.

The 101w Mood music channels load properly and work for myself and others. I do not know what needs to be fixed in the 101w Mood music channels without more information. The pids for the Mood music channels are correct.
 
Back
Top