Satdreamgr and ATSC

eastof111

eastof111

BinThere
Administrator
I had some time to experiment and load the latest Satdreamgr in flash to check out the atsc epg. I removed the Sundtek usb tuner and deleted the .sh file, but left the control center alone. Then I tried individually, the three Hauppauge driver versions but the image would not recognize the wintv 850 usb tuner.

The only way to get it recognized was to do the opkg install routine. Once recognized, it scanned all the stations and has an epg assigned to some 30% of channels. Some problems still exists for me. Still have to keep using engima restart from the menu in order to activate the usb tuner. Also, when receiver is shut down over night, it needs two or more cold boots to activate the receiver. Then it needs engima restart from the menu to activate the usb tuner.

I'll probably post on the Satdreamgr site too.
 
Try loading the latest from OpenPLi and see if you have the same issues. Download the driver from downloadable plugins for your Hauppauge device. Ignore the 950 and 955 drivers. No need to use telnet.
 
Played some more earlier with ATV since it had the same drivers available. Loaded the main driver, not 950 or 955 and it recognized the usb tuner. But, when I went to the tuner config menu, it displayed as enabled, but it would not allow me to select the atsc settings menu for the tuner.

I'll give PLI a shot tomorrow and post the results.
 
What you are seeing in OpenATV is the tuner being recognized and nothing else. In other words, enigma2 "sees" the tuner but does not know what it is or what it is supposed to do. They will probably finish it one day. All the needed information is available.
ATSC works in OpenVix.
 
Looks like VIX is the first OE Aliance based image with ATSC support! You will need to manually add the atsc.xml file to etc/tuxbox for a complete manual scan. This file is missing from the current 4.2.012 build.

View attachment 13447


Vix_Info.webp
 
OpenPLi and SatDreamGr EPG populates out 24 hours for me on some muxes. The channel has to be watched for several minutes to have the guide populate this far. Currently OpenVix only has now/next EPG.
 
I am still on Satdreamgr and haven't had a chance to try Vix or Pli. Had to change all my timers (10) for recording due to the time change. Forgot all about it and missed some recordings. The epg now shows standard time, but the actual info for the channel is one hour off. We use MST all year in my area.

Would be nice to have a check, uncheck box in the timers and/or epg menus to compensate for the Spring and Autumn changes in applicable time zones. Not complaining, just suggesting. I am grateful the timers work as well as they do now.
 
s the epg populating using the epg button? I Am guessing you are not using the latest available updates? There were problems like you mention early on but they seem to have been resolved.

You can also set the receiver to get the time from ATSC. You need to also set an ATSC channel that the receiver goes to when first started if you use ATSC transponder time.
 
el bandido said:
s the epg populating using the epg button? I Am guessing you are not using the latest available updates? There were problems like you mention early on but they seem to have been resolved.

I am using the latest updated Satdreamgr. Last night it was still having these epg problems, but not on all channels. Today after a cold boot and enigma restart for the usb tuner, it seems to be behaving in regards to the hour vs. description compared to the actual program on display.

You can also set the receiver to get the time from ATSC. You need to also set an ATSC channel that the receiver goes to when first started if you use ATSC transponder time.

I always use internet time because of all the timers I have setup with very close start/end times and switching between atsc and sat channels could create conflicts.

Will check tonight's recordings to see how it goes.
Click to expand...
.
 
Updated SDG online today and after the reboot, everything in the Channel Selector listing was N/A. Similar to what was discussed in the OpenPLI lamedb vs. lamedb5 thread.

Had to do a manual scan for atsc and all returned to normal after the scan. Hope they correct this soon.
 
eastof111 said:
Updated SDG online today and after the reboot, everything in the Channel Selector listing was N/A. Similar to what was discussed in the OpenPLI lamedb vs. lamedb5 thread.

Had to do a manual scan for atsc and all returned to normal after the scan. Hope they correct this soon.
Click to expand...

This problem should be fixed now. I downloaded 11-22 experimental, and it installed without any channel issues. A few previous images would turn some channels red.
 
Seems ok here as well, I did an online update yesterday and no problems this time with the channels being red.
 
Very Good!
A reminder:
Lots of changes are being made to enigmna2 right now by all of the major groups. Some of these changes will cause unwanted problems or issues, It is a good idea to make regular backups, or at least do a backup of your settings before flashing or doing an online update of the image.
 
Back
Top