el bandido
TNAP-Images
The Titanimu ASC! or ASC-1 was released several years ago as a dish positioner with several features no other positioner has. Unfortunately, the software for the ASC1 had a few bugs that were never eliminated. Some time ago, I was gifted some ASC1 units and have been waiting for the right time to do something with them. That time seems to be Now.
I have been able to take the ASC1 software apart and examine it. While it is somewhat tricky to make edits to the ASC1 software, I think it is "Doable", but there is an outside possibility in bricking the device. While I am not interested in disabling an ASC1, I do have extra units which puts me in a unique position to try some software edits. Once the software is tested and proven safe, it can be distributed to others.
I will target 2 things with the first edit attempt and add a third.
(1) There will be an attempt to show coast counts. Currently when the ASC1 removes power from the actuator, the counts stop. In dish systems with worn parts, the actuator can continue to move for a bit and the operator cannot see it. The first edit will allow the counts to progress for a short period after the power is removed from the actuator.
(2) The second edit will address the ASC1 losing its position after the power blinks.
The position is saved every time the dish comes to rest.
The stock firmware only saved it during a power failure, and that save took long enough that a quick flicker could interrupt it. CF2 keeps the position and satellite number in 16 rotating slots in unused EEPROM, each with a checksum. At power-up it uses the newest good slot, never zero or garbage. If the dish hasn’t moved since the last save, a power dip writes nothing at all.
Power-blink guards:
DiSEqC commands are ignored for 2 s after power-up (the boot timing problem Titanium described).
Reset SAT data, Reset soft limit, Reset position and Global Reset are refused for 2 s after power-up and after any supply dip. A dip can look like a key press, and that’s my best explanation for lists coming back blank after storms.
In normal use, just wait 2 s and press again.
(3) Add onscreen metrics to the FTA receiver.
By utilizing RS232 port, we have the possibility of adding onscreen information about what the ASC1 is doing or what the ASC1 has done. This feature will require cabling from the receiver to the ASC1 as the RS232 ports on the FTA receiver and the ASC1 have to be connected. This addition hopefully will mean no more looking at a small display for information! ...We will see eh???
What I would like if possible is a full description of how the software failed from anyone that is currently using the unit. The edits I mentioned above have already been made and written. Now i will need to dig out a RS232 cable and flash one of the ASC1's and see what happens. Again, I am not interested in bricking the unit. But I do have spare or extra ASC1's which puts me in a very unique position to try this.
I have been able to take the ASC1 software apart and examine it. While it is somewhat tricky to make edits to the ASC1 software, I think it is "Doable", but there is an outside possibility in bricking the device. While I am not interested in disabling an ASC1, I do have extra units which puts me in a unique position to try some software edits. Once the software is tested and proven safe, it can be distributed to others.
I will target 2 things with the first edit attempt and add a third.
(1) There will be an attempt to show coast counts. Currently when the ASC1 removes power from the actuator, the counts stop. In dish systems with worn parts, the actuator can continue to move for a bit and the operator cannot see it. The first edit will allow the counts to progress for a short period after the power is removed from the actuator.
(2) The second edit will address the ASC1 losing its position after the power blinks.
The position is saved every time the dish comes to rest.
The stock firmware only saved it during a power failure, and that save took long enough that a quick flicker could interrupt it. CF2 keeps the position and satellite number in 16 rotating slots in unused EEPROM, each with a checksum. At power-up it uses the newest good slot, never zero or garbage. If the dish hasn’t moved since the last save, a power dip writes nothing at all.
Power-blink guards:
DiSEqC commands are ignored for 2 s after power-up (the boot timing problem Titanium described).
Reset SAT data, Reset soft limit, Reset position and Global Reset are refused for 2 s after power-up and after any supply dip. A dip can look like a key press, and that’s my best explanation for lists coming back blank after storms.
In normal use, just wait 2 s and press again.
(3) Add onscreen metrics to the FTA receiver.
By utilizing RS232 port, we have the possibility of adding onscreen information about what the ASC1 is doing or what the ASC1 has done. This feature will require cabling from the receiver to the ASC1 as the RS232 ports on the FTA receiver and the ASC1 have to be connected. This addition hopefully will mean no more looking at a small display for information! ...We will see eh???
What I would like if possible is a full description of how the software failed from anyone that is currently using the unit. The edits I mentioned above have already been made and written. Now i will need to dig out a RS232 cable and flash one of the ASC1's and see what happens. Again, I am not interested in bricking the unit. But I do have spare or extra ASC1's which puts me in a very unique position to try this.