TNAP-7 Image Discussion

Unzip the attached file. Place octagon-blindscan into /usr/bin of the ustym4kpro receiver.

Then using Telnet or Terminal:
chmod +x /usr/bin/octagon-blindscan
reboot


Satellite Blindscan will work.
The Ustym4K Pro’s Blindscan now works perfectly
It automatically detects a 500 SR, and the Ustym reads a 333 SR without any problems
 

Attachments

  • blindscan sr500.webp
    blindscan sr500.webp
    28.3 KB · Views: 16
  • SR333.webp
    SR333.webp
    44.2 KB · Views: 14
Been using the VU+zero4k today. I set up multiboot on it using openatv so what can be done is have two versions of TNAP 7. One with the Radio fix (10/24 image) and one without and when we want to use the AAC radio just boot in that slot. Normal everyday TV use another slot. That audio sync issue is seen on Satellite timeshift and recordings on all services ATSC. Multiboot and TNAP7 has really made this zero4k great again. Thanks.
Didn't know that this box can be set to have mooltiboot. How many slots can you set on it ?
 
Didn't know that this box can be set to have mooltiboot. How many slots can you set on it ?
I have four slots but the main image Openatv is slot 0 or R after multiboot is created using the multiboot manager. Then 1,2,3 is really in the root of slot 0. You can use slot 0 but if you want to make a full image backup of slot 0 it will take a long time. Large size. I am only going to use slots 1,2 and 3 for backups and keeping those slots up to date. You can flash another copy of Openatv in slot 1,2 or 3. That way it can be kept updated and make full image backups faster.
I am sure there is other ways to setup the multiboot but that is the only method I have used.
 
I did follow the instructions from here: multiboot
I have Vix in slot1, but when I try to flash the backup of tnap7, I get this error
(?!?):
 

Attachments

  • Vu0-multiboot.webp
    Vu0-multiboot.webp
    152.7 KB · Views: 11
I did follow the instructions from here: multiboot
I have Vix in slot1, but when I try to flash the backup of tnap7, I get this error
(?!?):
I Flashed vix as root and set up the multiboot then flashed my backup of TNAP 7 without any problem.
We should make a new thread in the VU+ zero 4k section about multiboot. Don't think this has any think to do with TNAP 7.
 
The tuner on my Octagon is malfunctioning, so I installed TNAP 7 on my Vuzero4k. The blind scan is almost perfect, except for a few glitches on 131w and 99w with the ABCs. I know the TP; it’s not a problem—I just add it manually and it fixes itself. I struggled a bit with the wireless setup, but once I noticed it has a dedicated section for DNS, the rest was very easy to set up.I’ve noticed that switching between channels on this device tends to be slow; I’m not sure if it’s the skin (Youchie) or something else I’m not familiar with that’s causing the slowness.I’ll admit the firmware image is very good for this device now; I’d previously tried other images that had significant issues with the blindscan feature.
 
Unfortunately, the blind scan does not work at all; it is still searching using the blind scan settings for the SF 8008 (Octagon), which is incorrect.
Many menus still refer to the 8008 (for example, the signal finder), even though this is an Ustym 4K PRO.
In terms of hardware - both receivers are identical, essentially, only the bootloader determines whether the device will be called USTYM or OCTAGON.
 
TNAP-7 / SF8008 – local MP4s won't play after today's online update (exteplayer3 v183)

Box: Octagon SF8008 v3, TNAP-7 in multiboot slot

After running the online update this morning (Nov 4), none of my local MP4 videos will play from the movie list. Booting an older TNAP image in another slot plays the same files fine.

What happens: ServiceApp hands the file to exteplayer3 (reports version 183). It opens the file without errors (H.264 640x480, audio A_IPCM, embedded S_TEXT/MOV subtitle) and reports the correct length, but the position stays at "ms":0 the whole time. The read-ahead counter runs through the entire file in about 14 seconds, then it logs "Frame read error: 'End of file'" and drops back to the movie list. No picture, no sound.

The files have PCM audio (A_IPCM), so the new exteplayer3 build may not be handling PCM in MP4 properly.

Workaround: Menu > Setup > System > Expert > Playback, recording and timeshift > ServiceApp, change player from exteplayer3 to gstplayer. Playback then works normally.

I have the full Enigma2 debug log if anyone wants it.
 
Always if possible, post a log. Look in the About page of the older image that works and provide the exact build information. Also, if possible, provide the output of this telnet command for both images. Thanks.

opkg list-installed | grep -i -E "exteplayer|serviceapp"
 
Today’s build of:
screenshot_2026-11-04_13-23-31.webp

SF8008v3 -> 192.168.132.115:22

root@sf8008:~# opkg list-installed | grep -i -E "exteplayer|serviceapp"
enigma2-plugin-systemplugins-serviceapp - 0.5+git217+95e5a4f0+95e5a4f41d-r1.tnap1
exteplayer3 - 183+git189+8a053dc0+8a053dcd8a-r0
root@sf8008:~#

Older build:

screenshot_2026-11-04_13-28-20.webp

SF8008v3 -> 192.168.132.115:22

root@sf8008:~# opkg list-installed | grep -i -E "exteplayer|serviceapp"
enigma2-plugin-systemplugins-serviceapp - 0.5+git217+95e5a4f0+95e5a4f41d-r1.tnap1
exteplayer3 - 183+git158+7c2ca050+7c2ca05b98-r0
root@sf8008:~#
 

Attachments

Is this the working slot?
root@sf8008:~# opkg list-installed | grep -i -E "exteplayer|serviceapp"
enigma2-plugin-systemplugins-serviceapp - 0.5+git217+95e5a4f0+95e5a4f41d-r1.tnap1
exteplayer3 - 183+git158+7c2ca050+7c2ca05b98-r0
root@sf8008:~#
 
Scheduled Maintenance of the Server:

"The servers below are scheduled for maintenance on the dates shown, between 10:00 AM and 10:00 PM Eastern Time. Each server is offline for a maximum of up to 3 hours within that window. IP addresses do not change."

Should be back soon. Thanks for reporting it.

Edit: Should be online now.
 
Back
Top